1 0
    PROMOTION FREE software bundles available on select oscilloscope and spectrum analyzer purchases through December 31, 2026.See Eligible Models →
    New

    UT-P07B

    500 MHz 10:1 General Purpose Oscilloscope Probe

    $119.00
    Sale Contact Us For Lead Time

    Backordered. Contact us for lead time.

    REQUEST A QUOTE

    500 MHz 10:1 passive oscilloscope probe with 10 MΩ / 12 pF tip loading, 9–54 pF compensation range and a 300 V RMS CAT II rating, for 1 MΩ oscilloscope inputs.

    View full details

    UT-P07B 500 MHz 10:1 General Purpose Oscilloscope Probe

    Overview

    The UT-P07B is a 500 MHz, 10:1 passive oscilloscope probe for general-purpose measurement on oscilloscopes with a 1 MΩ input. It presents 10 MΩ and 12 pF at the tip, compensates inputs from 9 pF to 54 pF, and is rated 300 V RMS CAT II.

    A replaceable 0.5 mm needle tip, a sprung hook, a ground spring needle and an alligator ground lead cover the usual ways of reaching a test point, and the 1.2 m cable weighs 40 g at the probe head.

    Key Features

    • 500 MHz bandwidth — DC to 500 MHz at −3 dB.
    • 10:1 attenuation, 10 MΩ / 12 pF — light loading on the circuit under test; the probe signals ×10 to scopes with a readout pin.
    • 9–54 pF compensation range — matches the input capacitance of most 1 MΩ oscilloscope inputs.
    • 300 V RMS CAT II — maximum working voltage; it derates as signal frequency rises.
    • Four ground and tip options — ground needle, ground spring needle, alligator ground lead and sprung hook.
    • Replaceable needle tip — a worn or bent tip is swapped by hand or with pliers.

    UT-P07B Details

    Short ground, cleaner edges

    The ground spring needle keeps the ground loop short. The manual's guidance is to ground as close to the component as possible: a smaller loop picks up less noise and preserves bandwidth.

    Compensate before you measure

    Connect the tip to the oscilloscope's 1 kHz calibration square wave (about 2 Vpp) and turn the trimmer at the BNC end until the top of the square wave is flat. An under- or over-compensated probe cannot meet its specification.

    Applications

    • Embedded and digital debug — clocks, buses and logic levels on boards under development.
    • Power electronics, low-voltage side — control signals and gate-drive logic within the probe's CAT II rating.
    • Teaching and service benches — a general-purpose probe for 1 MΩ oscilloscope inputs up to 500 MHz.

    Compatibility

    Works with oscilloscopes that have a 1 MΩ BNC input. For a lower-cost 500 MHz option see the UT-P07A; for signals that need more bandwidth or less loading, see the UT-PA1000 and UT-PA2000 active probes.

    Frequently Asked Questions

    What is the maximum voltage?

    300 V RMS, CAT II. The rating falls as the signal frequency rises, and the probe must not be used for CAT III or CAT IV measurements.

    Does it work with a 50 Ω input?

    No. It is a 1 MΩ-input probe; set the oscilloscope channel to 1 MΩ.

    How do I compensate it?

    Probe the oscilloscope's 1 kHz calibration output and adjust the trimmer at the BNC connector until the square wave has a flat top.

    Warranty

    This product includes a standard 1-year warranty covering manufacturing defects and component failures under normal use conditions.

    UNI-T stands behind every product we sell. If you experience any issues within the warranty period, our US-based support team is here to help with troubleshooting, repair, or replacement.